Buy Chef's Choice 667 International Professional Electric Food Slicer with 10-Inch Diameter BladeChef's Choice 667 International Professional Electric Food Slicer with 10-Inch Diameter Blade Product Description:
- Rugged, commercial quality, die cast metal construction
- Tilted design for fast and efficient slicing
- Heavy duty powerful induction motor for extremely quiet operation
- Larger capacity food carriage, rides smoothly on industrial ball bearings and retracts fully to fit extra large roasts, hams, etc.
- Dimensions 21 by 14.6 by 14.5 inches; weighs 30 pounds
Product Description
087877667000 Features: -Tilted design for fast and efficient slicing.-Powerful induction motor for extremely quiet operation.-Precision thickness control from deli-thin to 9/16.-Commercial quality, fully hardened, stainless steel blade, diameter 9.8 (25 cm).-Large capacity food carriage for extra large roasts, hams etc...-Peak power over horsepower. Includes: -Includes blade sharpener and convenient food tray. Construction: -Rugged, commercial quality die-crust metal construction. Dimensions: -Weight: 31.6 lbs.
Customer Reviews
Most helpful customer reviews
155 of 157 people found the following review helpful.
Almost "Professional"
By ducrab
The Chef's Choice 667 slicer performs as advertised with its sturdy construction, powerful motor, large 10" belt-driven blade, and smooth quiet operation. This slicer does indeed produce deli-thin slices!
Out of the Box
The Chef's Choice 667 slicer comes out of the box with a 10" stainless-steel blade, blade sharpener, owner's manual, Allen wrench, small plastic serving tray, and temporary blade guard used for handling the sharp blade.
The plastic blade guard easily screws onto the blade using two large plastic knobs. This temporary guard covers the razor sharp edge of the blade and makes it easy to handle when it's removed from the slicer or during cleaning.
The plastic food tray is used to catch the food as it's being sliced, but it's too small and does not fit squarely under the blade.
The Allen wrench is used for removing the main blade guard during cleaning.
The blade sharpener is attached to the top of the unit and is held in place by a thumb screw. Simply loosen the screw, lift, and pivot the sharpener into place. A rear-mounted grinding wheel sharpens the blade while a front spring-loaded push-in grinding wheel removes any burrs.
The included non-serrated blade is excellent for slicing meats, vegetables, cheeses, etc., but is not well suited for breads. To slice bread you'll want to buy the optional serrated blade (~$90).
First Impressions
Operating the slicer is straightforward. Plug in the unit, load the carriage with the food to be sliced, flip the on/off switch to "on", and finally press the safety interlock switch. The interlock switch prevents the unit from starting up should the on/off switch be left on while plugging it in, a nice safety feature!
Once powered on, you must exert some pressure on the food pusher and slide the carriage forward and back while setting the thickness knob to your desired setting.
The slicer itself is very sturdy and appears to be well made. The main body is made of die-cast metal and the blade stainless steel. The carriage is smooth and rides on a single ball bearing. The motor/blade is powerful and is belt driven.
Some parts of the slicer utilize plastic screws, namely the friction adjustments for the sliding carriage and the thickness dial. There is also a small plastic piece which keeps the food pusher from scraping the carriage. This plastic piece fell out of its hole while I was operating the unit. I used SuperGlue to reattach.
The carriage is secured to the sliding arm with two bolts and small thumb nuts. These small nuts are awkward to remove and/or tighten and require the use of pliers. The bolt holes are slightly oversized and require lock washers, which I do not like. I would have preferred larger nuts (or knobs) and properly sized bolt holes to facilitate easy removal and reinstallation of the carriage tray.
The travel on the food pusher is somewhat limited and you may have to cut large roasts in half so they'll fit in the carriage. The bushings on the food pusher arm rod are made of plastic, I would have preferred brass or some other material.
Slice thickness is controlled by a large knob calibrated in millimeters. Maximum thickness is 0.6 inches. Once set, I didn't have to make any further adjustments. Friction is set by a plastic screw inside the base of the unit.
The bottom of the slicer is covered with a black plastic cover which seems a little flimsy for a "commercial quality" slicer. Four screws and four rubber feet secure the bottom cover to the unit.
The unit is moderately heavy, roughly 30 pounds, and it stays put on the counter.
First Experience
My first experience with this slicer was making thin sliced (almost shaved) roast beef sandwiches. I slow roasted a 10 pound Sirloin tip roast until it was rare and juicy. The slicer effortlessly sliced the meat to perfection. The motor showed no signs of stress and the carriage moved smoothly and easily.
This is my second food slicer. My first was an inexpensive Rival slicer which could not handle roast beef. It was noisy, flimsy, and downright dangerous to use. The cuts were uneven, thicker at the top and thinner at the bottom. I was worried that getting paper thin slices from a consumer-grade slicer was not possible. The 667 proved me wrong. It surpassed all of my expectations and performed similarly to the big Hobarts that I've used in the past.
Caveats
I do have some major complaints about this otherwise excellent slicer.
There are several joints in the housing of this slicer which allow meat juices drip inside the body of the unit. One such joint is located right where the motor housing attaches to the main base. This joint is located right where the sliced food falls as it's being cut, a very poor design. There is another joint where the blade thickness arm protrudes through the base. Juices from my roast beef dripped into the base of the slicer through these joints and started dripping out near one of the rubber feet on the opposite end of the unit. Yuk! The only way to clean up this mess was to remove the screws, rubber feet, and plastic cover from the bottom of the slicer. One shouldn't have to disassemble an appliance to properly clean it!
Also, to remove and clean the blade, you must use the Allen wrench to remove a single screw in the center of the front blade guard (poor design). Next you attach the plastic blade guard. Finally, using a screwdriver, you must remove three Phillips-head screws which secure the blade to the spindle. Not only is this inconvenient, but the screw heads will eventually wear and/or strip after repeated cleanings. Note: The blade should be removed to thoroughly clean the slicer since it's difficult to clean behind the blade. Another poor design.
In Summary
Overall, I am very happy with the performance of this slicer. It's sturdy, powerful, quiet, and slices exceptionally well. However, clean-up is another story.
This slicer is definitely "consumer grade" (not "commercial grade" as advertised) and will make a fine addition to any gourmet kitchen. When slicing juicy foods, I'd recommend using lots of paper towels placed strategically to catch the liquids before they can get inside the unit.
30 of 31 people found the following review helpful.
Go Ahead & Spend the Money, You Won't Be Sorry!
By Kcoruol
This is the second food slicer I've owned in my life. The first was a Waring food slicer I picked up at Lowes for about a hundred bucks. I returned it the next day. So I came to Amazon.com and decided to buy this model. While it is an invested in money and kitchen space, I'm very happy with it. It slices through meat, cheese, and veges like they were nothing. Plenty of hand guards and saftey features to keep you from slicing your fingers off too. The blade is extremely sharp though and should be handled with extreme care. Just remember, don't put your fingers near the blade while it's spinning for any reason. It does come with a plastic carry case which screws on to the blade so it can be removed for cleaning. I wouldn't recommend handling the blade with out it as the blade is razor sharp and rather heavy. The machine is easy to clean and the blade can be removed and replaced in a few minutes. It's simple, it's easy, and it's slices great. I bought some roast beef, ham, and turkey at Sam's club and this machine will slice the meat very very thin which is the way I like it!. Now, I know you're looking at the price and thinking, that's a lot of money. All I can say is don't waste your money on some cheap brand, spend a little more and get a quality piece of kitchen equipment that will do the job and do it right. The only draw back I can see is the size, which for me isn't a problem, but if you're looking for something small, this isn't it. It's not as big as the slicers you see at the deli, but it's close. I'd also recommend a food vacuum machine so you can vacuum seal the unused meat for later to keep it fresh or even so you can freeze a portion of it for later. Also, don't slice it until you are ready to eat it. I know once you get this baby home, you'll want to slice that whole 6lb roast beef, just slice what you're going to use and refrigerate or freeze the rest for later. One more thing, always turn the thickness knob to zero when you're not cutting food, just a safety measure. All I can say is if you're in the market for a good slicer, don't look and further, I think everybody would be happy with this model!!
34 of 37 people found the following review helpful.Don't forget to consider this!
By fw Bear
Yes it is true that this thing really does slice as a $400 slicer should. That is a given and the reviews here show people agree it does the job.But two things to consider:1) $460 -IS- a lot of money. But you make the decision that you are willing to pay that for your own professional slicer.2) The BIGGER thing to consider is ARE YOU PREPARED TO CLEAN THIS MACHINE EVERY TIME YOU USE IT???Remember, at the delicatessen or market, the Jr. butcher has the task of cleaning it every night.This thing requires that you take apart the feed tray, blade cover, blade etc., to gain access to the bits of food lodged within. It -IS- well designed and easy to dis-assemble and re-assemble, but it does TAKE TIME.And if you leave it for a day or two, you will have a very hard task to scrape out the hardened food bits.I love it. I'm glad I bought it. I enjoy being able to shave ham and turkey tissue thin for my sandwiches instead of constantly telling the dude at the delicatessen "Thinner ! - Thinner!!".You should understand that you pay Amazon for this when you buy it, and you pay again to clean it after every use.It is worth it to me. Is it to you?
Latest Price: See on Amazon.com!
More Info: See on Amazon.com!
See Customers Review: See on Amazon.com!
